Document from CIS Legislation database © 2003-2023 SojuzPravoInform LLC

Registered by the

Ministry of Justice

Republic of Uzbekistan

On September 28, 2005 No. 1513

ORDER OF THE UZBEK AGENCY OF STANDARDIZATION, METROLOGY AND CERTIFICATIONS (UZSTANDART)

of September 7, 2005 No. 340

About approval of Rules of certification on separate types of products which are subject to obligatory certification

(as amended on 03-03-2015)

According to Item 6 of the resolution of the Cabinet of Ministers of the Republic of Uzbekistan of July 6, 2004 to № 318 "About additional measures for simplification of the procedure of certification of products", I order:

1. Approve Rules of certification on separate types of products which are subject to obligatory certification.

2. Enact this Order after ten days from the date of its state registration in the Ministry of Justice of the Republic of Uzbekistan.

CEO

R.A.Buriyev

Approved by the Order of the CEO of the Uzbek agency of standardization, metrology and certification of September 7, 2005 No. 340

Rules of certification on separate types of products which are subject to obligatory certification

These rules are developed according to Item 6 of the resolution of the Cabinet of Ministers of the Republic of Uzbekistan of July 6, 2004 No. 318 "About additional measures for simplification of the procedure of certification of products" (Collection of the legislation of the Republic of Uzbekistan, 2004, No. 27, Art. 315) and establish specifics of certification of separate types of products, subjects of obligatory certification.

I. General provisions

1. Certification of products is performed according to Rules of certification of products (reg. No. 1458 of February 25, 2005, the Collection of the legislation of the Republic of Uzbekistan, 2005, Art. No. No. 10-11, 86), taking into account specifics of certification of products, the provided these rules.

2. Before selection of products identification of the shown samples specified in the request is carried out. As identifiers serve marking and the accompanying document.

3. Testing of products for the purpose of certification are performed on safety indicators according to the established requirements of the operating ND.

The amount of certification tests can be reduced in case of presentation by the applicant of the test reports of products fulfilled testing in laboratory of body of the state sanitary inspection or other accredited test laboratories taking into account terms of frequency of carrying out the testing established by ND.

4. In case of inspection of condition of production the following is analyzed:

a) availability of the regulating documentation (further - ND) on the products declared to certification;

b) availability and condition of laboratory, or the contract with the laboratory exercising quality control of raw materials and finished goods;

c) equipment of engineering procedures in case of production by processing equipment, measuring instruments and their condition (checking);

d) observance of the technological modes in case of production;

e) availability of the specialists exercising production and control of products;

e) availability of storage conditions and transportation of finished goods and raw materials.

By results of inspection of conditions of production the statement of inspection which is one of the bases for issue of the certificate of conformity is drawn up.

II. Specifics of certification of food products

5. In case of certification of food products schemes No. No. 3, of 4, of 7, 9 can be applied.

6. Testing of food products for the purpose of certification are performed on safety indicators according to the established requirements of the operating ND. When testing products on indicators of safety control of products on physicochemical indicators, industrial sterility, mass fraction of toxic elements, nitrosamines, histamine, the polychlorinated biphenyls, pesticides, mycotoxins is carried out, including aflatoxins, antibiotics, radionuclides, microbiological indicators, content of nitrites, harmful impurity and contamination by wreckers (for grain and products of their conversion), oxymethylfurfural, mineral substances and vitamins, extent of genetic modification in the presence of requirements in ND, and also according to mandatory requirements, including indicators of marking and packaging, according to the established requirements of ND of specific type of food products.

III. Specifics of certification of electrotechnical products

7. In case of certification of electrotechnical products schemes No. No. 1, of 2, of 3, of 4, of 7, 8 and 9 can be applied.

8. When testing electrotechnical products on indicators of safety control of products on insulation resistance, electrodurability of isolation, requirements to design, residual stress, completeness, mechanical durability, vibration strength, endurance to voltage variation, climatic testing for moisture resistance, cold constancy and heat resistance, radio noise, efficiency, crash-worthiness, potential of explosion, fire danger, to testing on the starter mode, current leakages, mechanical durability of connections, working capacity on functioning, to free fall, the heating of surface increased and the lowered tension, lighting indicators, and also according to mandatory requirements, including indicators of marking and packaging, according to the established requirements of ND of specific type of the certified electrotechnical products is carried out.

IV. Specifics of certification of products of mechanical engineering and heavy industry

9. In case of certification of products of mechanical engineering and the heavy industry schemes No. 31, of 2, of 3, of 4, of 7, of 8, 9 can be applied.

10. When testing products of mechanical engineering and the heavy industry on indicators of safety control of products on organoleptic, physicomechanical indicators, technical requirements, and also according to mandatory requirements, including indicators of marking and packaging, noise and vibration characteristics, harmful emissions in the atmosphere, the indicators influencing the environment according to the established requirements of ND of specific type of products of mechanical engineering and the heavy industry is carried out.

V. Specifics of certification of products of light industry

11. In case of certification of products of light industry schemes No. No. 3, of 4, 7 can be applied.

Warning!!!

This is not a full text of document! Document shown in Demo mode!

If you have active License, please Login, or get License for Full Access.

With Full access you can get: full text of document, original text of document in Russian, attachments (if exist) and see History and Statistics of your work.

Get License for Full Access Now

Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info

Effectively work with search system

Database include more 50000 documents. You can find needed documents using search system. For effective work you can mix any on documents parameters: country, documents type, date range, teams or tags.
More about search system

Get help

If you cannot find the required document, or you do not know where to begin, go to Help section.

In this section, we’ve tried to describe in detail the features and capabilities of the system, as well as the most effective techniques for working with the database.

You also may open the section Frequently asked questions. This section provides answers to questions set by users.

Search engine created by SojuzPravoInform LLC. UI/UX design by Intelliants.