Document from CIS Legislation database © 2003-2022 SojuzPravoInform LLC

The document ceased to be valid since  February 10, 2016 according to the Resolution of the Cabinet of Ministers of Ukraine of December 30, 2015 No. 1184

RESOLUTION OF THE CABINET OF MINISTERS OF UKRAINE

of November 29, 2001 No. 1599

About approval of the description and rules of application of national mark of conformity

(as amended on 06-08-2014)

According to part one of article 33 of the Law of Ukraine "About standards, technical regulations and assessment procedures of compliance" the Cabinet of Ministers of Ukraine decides:

Approve the description and rules of application of national mark of conformity (are applied).

Prime Minister of Ukraine

A. Kinakh

Approved by the Resolution of the Cabinet of Ministers of Ukraine of November 29, 2001 No. 1599

Description of national mark of conformity

The national mark of conformity (further - mark of conformity) has the form of the main circle which is not closed on the right side in which the stylized image of trekhlistnik is placed.

Three (average and two side) tops of trekhlistnik (with internal corners of 30 degrees) are placed in the upper part of the imagined circle with the radius constituting 0,7 of radius of the main circle, and the fourth (with internal corner of 80 degrees) - in the lower part. The average top is the upper point of the imagined circle, two bokovyerazmeshchenny symmetrically at an angle 15 degrees to the horizontal line passing through its center. The fourth (lower) top is at distance of 0,6 of radius of the main circle on the vertical line passing through its center.

On the middle of the straight line connecting the center of circle to the lower top there is conditional center of trekhlistnik which leaves six beams. Four of them connect this point to tops of trekhlistnik, and two - points of intersection of sidelines of the corner formed by average top with the horizontal line which passes through the center of the imagined circle. The planes of triangles of trekhlistnik to the left of beams which connect its center with side and average tops have the same color, as the image of sign.

Length of gap of the main circle constitutes 0, it total length (or 80 degrees). Thickness of lines of trekhlistnik - circle radius 0,01. Thickness of the line of circle - circle radius 0,05.

The image of mark of conformity can be flat or relief and is carried out by two contrast colors.

The image of mark of conformity can be executed by any technological method providing its clearness and legibility current of all term of use of product. By technical regulations additional requirements concerning accomplishment of the image of mark of conformity can be established.

The size of mark of conformity is determined by the producer or the product supplier proceeding from specific conditions and the place of its drawing, but there cannot be less than 5 millimeters if another is not provided corresponding technical
regulations.

Approved by the Resolution of the Cabinet of Ministers of Ukraine of November 29, 2001 No. 1599

Rules of application of national mark of conformity

1. The national mark of conformity (further - mark of conformity) certifies compliance to products designated by it to requirements of technical regulations which extend to it.

2. The mark of conformity is applied only on those types of products which description is located in technical regulations. At the same time drawing mark of conformity is obligatory.

3. In case of confirmation of conformity of products, the appointed conformity assessment body near mark of conformity puts identification code of this body according to the register of the appointed conformity assessment bodies.

4. The mark of conformity is applied on products with directly her producers if another is not provided by the corresponding technical regulation.

5. The mark of conformity is applied on product or on the label, container, packaging, the operational and shipping documentation in case of impossibility or not correctness of its drawing is direct on product if other is not provided by the corresponding technical regulation. The place and method of drawing (printing, gluing, engraving, etching, stamping, casting, etc.) mark of conformity is determined by the producer of products.

6. It is allowed to use the image of mark of conformity in advertizing of products designated by it.

7. Features of application of mark of conformity can be established by technical regulations.

 

Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info

Effectively work with search system

Database include more 50000 documents. You can find needed documents using search system. For effective work you can mix any on documents parameters: country, documents type, date range, teams or tags.
More about search system

Get help

If you cannot find the required document, or you do not know where to begin, go to Help section.

In this section, we’ve tried to describe in detail the features and capabilities of the system, as well as the most effective techniques for working with the database.

You also may open the section Frequently asked questions. This section provides answers to questions set by users.

Search engine created by SojuzPravoInform LLC. UI/UX design by Intelliants.