of June 9, 2023 No. 424
About approval of the Control list of specific goods
According to the subitem 5) of article 8 of the Law of the Republic of Kazakhstan "About control of specific goods" I ORDER:
1. Approve the enclosed Control list of specific goods.
2. To provide to committee of industrial development of the Ministry of the industry and infrastructure development of the Republic of Kazakhstan in the procedure established by the legislation:
1) state registration of this order in the Ministry of Justice of the Republic of Kazakhstan;
2) placement of this order on Internet resource of the Ministry of the industry and infrastructure development of the Republic of Kazakhstan.
3. To impose control of execution of this order on the supervising vice-minister of the industry and infrastructure development of the Republic of Kazakhstan.
4. This order becomes effective after ten calendar days after its first official publication.
Minister of the industry and infrastructure development of the Republic of Kazakhstan
M. Karabayev
|
It is approved Ministry of Agriculture of the Republic of Kazakhstan |
|
|
It is approved Ministry of science and the higher education of the Republic of Kazakhstan |
|
|
It is approved Ministry of Health of the Republic of Kazakhstan |
|
|
It is approved Ministry of Defence of the Republic of Kazakhstan |
|
|
It is approved Committee of homeland security of the Republic of Kazakhstan |
|
|
It is approved Ministry of digital development, innovations and aerospace industry of the Republic of Kazakhstan |
|
|
It is approved Ministry of Internal Affairs of the Republic of Kazakhstan |
|
|
It is approved Department of Energy of the Republic of Kazakhstan |
|
Appendix
to the Order of the Minister of the industry and infrastructure development of the Republic of Kazakhstan of June 9, 2023 No. 424
General notes according to the list
1. For control over the goods developed or changed for military application address the corresponding list/-ам on control over military goods. References in this list with the text "Also to watch control over military goods" refer to the same lists.
2. The goods entered in this list shall not be exempted from licensing when exporting uncontrollable goods (including plants), the containing one or more controlled components being the main part of goods and can be easily removed or used for other application.
Special note: By consideration of controlled component or components for the purpose of their reference to the main part it is necessary to weigh such factors as quantity, value and the used technological know-how, and also the other special factors capable to determine the fact: whether the controlled component or components is the main part of acquired goods.
3. The goods specified in this list include both new, and being in the use.
4. The Commodity Nomenclatures of Foreign Economic Activity codes are referral and auxiliary codes in the course of identification and correlation of goods (services) to products double and military. The Commodity Nomenclatures of Foreign Economic Activity codes can be not complete or not cover all controlled line items, and can not correspond to technical parameters of controlled line item. The final decision to dual or military purpose is determined by identification and correlation of these or those products by technical parameters of controlled products of this list.
Use of the Commodity Nomenclatures of Foreign Economic Activity codes which are absent in the control list of specific goods is allowed.
5. The structure of the list of products of dual purpose consists of 10 categories which includes the following categories and parts:
Determination of the terms used in the list;
category 0 - nuclear materials, installations and the equipment;
category 1 - materials, chemicals, microorganisms and toxins;
category 2 - processing of materials;
category 3 - electronics;
category 4 - computer facilities;
category 5 - telecommunications and "information security";
part 1. telecommunications;
part 2. "information security";
category 6 - sensors and lasers;
category 7 - navigation equipment and aviation electronics;
category 8 - maritime case;
Category 9 - propulsion systems, spacecrafts and the accompanying equipment.
Category 10 - the products controlled within homeland security, which are not covered by categories 0-9.
Each category includes 5 technical groups of products of dual purpose:
And - the equipment, nodes and components;
In - the production and test equipment;
With - materials;
D - software;
Е - technologies.
In technical group the reference to multilateral and unilateral verification regimes of specific goods is had:
000-099 - vassenaarsky arrangements (VA);
100-199 - verification regime of rocket technologies (VRRT);
200-299 - group of nuclear suppliers (GNS);
300-399 - Australian group (AG);
400-499 - convention on prohibition of chemical weapon (KHO);
500-899 - reserve;
900-999 - the unilateral lists of products controlled within homeland security.
The note on nuclear technology
(Read together with part "E" of category 0)
The "technology" which is directly connected with any goods controlled in Category 0, is controlled according to Category 0 provisions.
"Technology" for "development", "production" or "use" of the goods which are under control remains under control even if it is applied in the relation to uncontrollable goods.
Approval of goods for export at the same time resolves export to this end user of minimum of "technologies" necessary for installation, work, maintenance and repair of goods.
Control over technologies broadcast does not extend to information in "the public sphere" or on "basic scientific research".
The general note on technology
(Read together with the Section "E" of Categories 1-9)
Export of the "technology" necessary for "development", "production" or "use" of the goods controlled by Categories 1-9, is controlled according to provisions of Categories 1-9.
"Technology" "necessary" for "development", "production" or "use" of the goods which are under control remains under control even in the relation to uncontrollable goods.
Control does not extend to "technology" which is necessary minimum for installation, work, technical support (check) and repair of those goods which are not controlled or whose export is resolved.
Special note: To data the "technology" specified in 1e002.e is not exempted., 1E002.f., 8e002.a., and 8E002.b.
Control over technologies broadcast does not extend to information in "the public sphere" or on "basic scientific research" or on minimum of necessary information for execution of the patent request.
The general note according to the software
(This note has priority over any control of the Section "D"
Categories 0-9)
Categories 0-9 of this list do not control "software" which or:
a) Availablly to public use, as:
1. Is on sale from warehouse in retail outlets without any limit by means of:
a. transactions for cash;
b. postal order;
c. electronic payment; or
d. order by phone; and
2. It is developed for installation by the consumer without essential further support from the supplier; or
Special note: The Item "and" of the General note after the software does not exempt the "software" specified in Category 5 - Part 2 ("Information security").
b) is in "the public sphere".
Determination of the terms used in the list
"Accuracy" (2, 6) - the size which is usually measured in the plan of error that means the maximum variation, positive or negative, the specified size from the accepted standard or correct value.
"Active management systems flight" (7) - the systems functioning for prevention of undesirable variations or structural loadings of "aircraft" and the rocket by means of autonomous processing of output signals of several measuring sensors and issue of necessary precautionary teams for the purpose of realization of automatic control.
"Active pixel" (6, 8) - the minimum (single) element of solid-state lattice having photo-electric transfer function in case of action of light (electromagnetic) radiation.
"Adapted for military application" (1) - undergone any modifications or selection on certain qualities (for example, by amount of impurity, storage life, virulence, transfer of properties, resistance to impact of ultra-violet radiation) for the purpose of increase in efficiency of impact on people and animals or deteriorations in characteristics of the equipment, fertility of the soil or the environment.
"Aircraft" (1, 7, 9) – aircraft with motionless wing, rotary wing, the rotating wing (helicopter), the rotary bearing screw or wing of changeable arrow-shapedness.
Special note: See also "civil aircraft".
"All available adjustments" (2) - means that the producer considered all almost feasible measures on minimization of all systematic errors of positioning for specific model of the machine.
"Allocation of frequencies on ITU" (3rd 5) - means that allocation of the range of frequencies is made according to Regulations on regulations of radio communication of International union of telecommunications (edition of 1998) for the main (primary), permitted and secondary communication services.
Special note: Additional and alternative allocation is not considered.
"Variation of angular provision" (2) - the maximum difference between angular provision and the valid provision on the corner measured with very high precision after the detail fixed after processing is turned rather starting position (see VDI/VDE 2617, Working option: "Tables of dependence of turn from mechanisms of measurement of coordinates".
"Asymmetric algorithm" (5) the cryptographic algorithm using different, mathematically dependent keys for coding and decoding means.
Special note: Example of practical use of "asymmetric algorithms" this management of key.
"Automatic maintenance of the purpose" (6) - processing method which automatically determines and provides as output signal extrapolated value of the most probable provision of the purpose in real time.
"Delay time of the basic logical element" (3) - the signal delay time corresponding to passing through the basic logical element used in "family" of "monolithic integrated circuits". It can be determined for this "family" or through delay time of passing of signal through typical logical element, or through typical delay time of passing of logical element.
Special note 1: "The delay time of the basic logical element" should not be confused to delay time between output and entrance signals of difficult "monolithic integrated circuit".
Special note 2: "Family" includes all set of the integrated circuits combined by the following signs which belong to the production technology and specifications, but do not concern their functional purpose:
a) identical architecture of integrated circuits and software;
b) identical design and the applied technology; and
c) identical main characteristics.
"Basic scientific research" - the experimental or theoretical works which are carried out mainly for the purpose of receipt of new knowledge of the fundamental principles or the observed facts, are not directed directly to achievement of the specific practical purpose or the solution of specific objective.
"Shift" (accelerometer) (7) - output signal of the accelerometer for lack of the enclosed acceleration.
"Beating" (2) - the radial shift for one turnover of the main spindle measured in the plane, perpendicular axis of spindle in measurement point on the external or internal surface of rotation (source - ISO 230/1 1986, paragraph 5. 63).
"Carbon fibrous preforms" (1) - it is arranged the uncovered or covered fibers located forming product framework which then is filled with "matrix" therefore "composition material" is created.
"VE" - is equivalent to "computing element".
"QUO" (circular probabilistic variation) (7) - the size measuring accuracy; radius of circle in which center there is purpose, at certain distance in which 50% of useful load are effective.
"The chemical laser" (6) - the laser in which the initiated circle is created due to output energy of chemical reaction.
"Chemical mix" (1) - the firm, liquid or gaseous product which turned out from two or more components which do not interact with each other in storage conditions of mix means.
"Control systems of the direction or antirotation with controlled circulation" (7) - control systems which use air flows along aerodynamic surfaces for strengthening or control of forces generated by surfaces.
"Civil aircraft" (1 7 9) - the "aircraft" listed according to designated in the published certified lists of the flight validity for flights on commercial civil internal and external airlines or legalized civil, private use or for the purposes of business.
Special note: See also "aircraft".
"Connected" (1) - the having interfaces of windings of thermoplastic fibers and hardening of fibers for the purpose of receipt of the combination reinforced by matrixes fibers in general fiber form.
"Crushing" (1) - process of crushing of material by means of grinding or sifting.
"Transfer on the general channel" (5) - transfer method in case of which on one channel, between stations, information concerning the number of channels or challenges or the other information used for management of network is transferred by means of the marked messages.
"The communication channel controller" (4) - the physical interface controlling flow of synchronous or asynchronous digital information. It is the block which can be built in the computer or the telecommunication equipment for ensuring access to communication use.
"Composition material" (1, 2, 6, 8, 9) – the "matrixes" and additional phase or additional phases consisting of particles, filamentary crystals, fibers or their any combination, developed for particular purpose or the purposes.
"Cumulative Theoretical Performance" ("CTP") (3, 4) - the measure of performance of calculations expressed in millions of theoretical operations per second (Мтопс), received as a result of aggregation of "computing elements" (CE).
Special note: See Category 4, the Technical note.
"The compound rotating table" (2) - the table allowing to rotate and incline detail around two nonparallel axes on which management can be coordinated for planimetric management".
"Computing Element" (CE) (4) - the smallest computing unit which performs arithmetic or logical operations.
"Planimetric management" (2) - movement on two or more axes with the "numerical control" which is performed according to instructions which determine the following required position and required feed rates to this provision. These feed rates vary in communication with each other, as forms required contour (see ISO/DIS 2806-1980).
"Critical temperature" (1 3 6) (sometimes called by transition temperature) certain "superconducting" material - temperature at which material completely loses resistance to passing of electric current.
"Cryptography" (5) - the discipline including the principles, means and methods of transformation of information for the purpose of concealment of its content, prevention of modification or unauthorized use. "Cryptography" is limited to transformation of information with use of one or more of "confidential parameters" (for example, cryptographic variables) or the relevant management of key.
Special note: "Confidential parameter" - constant or the key known only to certain group of persons and not giving information access for other persons.
"STP" - is equivalent to "cumulative theoretical performance".
"Navigation systems on the basis of reference databases" (7) - systems which use the different sources of the priori measurements of geocartographic data which are in a complex providing exact navigation information in case of the dynamic modes. Information sources include batimetrichesky cards, celestial maps, gravitational cards, magnetic cards or three-dimensional digital district maps.
"Deformable mirrors" (6) (known also as adaptive optical mirrors) - the mirrors having:
a. One the continuous optical reflecting surface which is deformed dynamically by means of appendix of separate forces or the twisting moments for compensation of misstatements of the optical signal falling on mirror; or
b. Multielement optical reflectors which provision separately and independently changes by means of appendix of separate forces or the twisting moments for compensation of misstatements of the optical signal falling on mirror.
"Depleted uranium" (0) - uranium in which content of isotope 235 is lower, than in natural uranium.
"Development" - all stages of works up to serial production, such, as: designing, project researches, the analysis of project options, development of concepts of designing, assembly and testing of prototypes (prototypes), creation of the scheme of pilot production and technical documentation, process of transfer of technical documentation in production, structural designing, prototyping.
"Diffusion welding" (1 2 9) - solid-phase connection at the molecular level of, at least, two separate metals in whole, with durability of connection, equivalent durability of compound of the weakest material.
"The digital COMPUTER" (the 4th 5) - the equipment which can perform all following functions in the form of one or more discrete variables:
a. Accept the entered data;
b. Store data or commands in constants or the changeable (rewriting) storage devices;
c. Store data or commands in constants or the changeable (rewriting) storage devices; and
d. Provide data output.
Special note: Modifications of the written-down sequence of teams include replacement of devices of permanent memory, but not change of the carried-out connections or contacts.
"Speed of digital transmission" - the general speed of information transfer in bits which is directly transmitted through any type of the circle.
Special note: See also "The general speed of digital transmission".
"Direct hydraulic pressing" (2) - process of deformation in which the flexible camera filled with liquid which is in direct contact with procurement is used.
"Drift speed" (gyroscope) (7) - derivative on variation time from required output signal. The component consists from accidental and systematic and it is expressed as the equivalent entrance angular shift of rather inertial space in unit of time.
"Dynamic adaptive routing" (5) - automatic change of route of transmission of messages on measurement base and the analysis of the current operating conditions of network.
Special note: Here cases of decisions on change of route of transmission of messages on the basis of previously being available information do not enter.
"Dynamic analyzers of signal" (3) - "signal analyzers" which use digital selection of signal and methods of its transformation for Fourier range receipt of this signal, including information on its amplitude and phase.
Special note: See also "signal analyzers".
"Effective gram" (0 1) - means to "the special split materials":
a. For isotopes of plutonium and uranium - 233 - isotope weight in grams;
b. For the uranium enriched with isotope uranium - 235 (1% or is more) - the element weight in grams increased by root square of the enrichment expressed as decimal share on weight;
c. For the uranium enriched with isotope uranium - 235 (less than 1%) - element weight in grams, increased by 0,0001;
"Electronic assembly" (3 4 5) - quantity of the electronic components (for example, "scheme elements", "discrete components", integrated circuits and so on) connected for accomplishment of certain function(s), which are subject to replacement and disassembly.
Special note 1: "Scheme element" - separate active or passive detail of the electronic scheme, such as one diode, transistor, resistor, condenser and so forth.
Special note 2: "Discrete component" - "scheme element" in the separate case with own external conclusions.
"The phased antenna lattice with electronic scanning of beam" (the 5th 6) - the antenna creating beam by means of the choice of phase ratios that is the direction of beam is controlled the choice of complex coefficients of excitement of radiating elements, and the direction of this beam can change on bearing angle and corner of the place or both by means of appendix of electric signal, both in case of acceptance, and by transfer.
"Working bodies" (2) - captures, "active tool nodes" and any other tools which fasten on basic lattice on the end of the manual manipulator of "robot".
Special note: "active tool nodes" - devices for appendix to procurement (detail) of measuring sensors or energy for its movement or processing.
"The equivalent density" (6) - the mass of optical units per unit of the optical area projected on optical surface.
"Expert systems" (7) - the systems which are providing results by means of application of rules to information which is stored irrespective of "program", and having any of the following characteristics:
a. Automatic modification of the source code (the text of the program) entered by the user;
b. Ensuring knowledge connected with some class of problems in quasinatural language; or
c. Acquisition of knowledge required for their development (symbolical training).
"PAETsKD" - "Completely autonomous electronic and digital controller of the engine".
"Fault tolerance" (4) - property of computer system after emergence of any defect in its hardware component or "software" to continue work without intervention of the person, to provide work continuity, integrity of data and recovery of work within the set time interval.
"Fibrous or threadlike materials" (0 1 2nd 8) - the materials including:
a. Continuous "threads";
b. Continuous "yarn" and "roving";
c. "Tapes", fabrics, accidental grids of any structure and band;
d. Cotton and linen fibers;
e. The reinforcing fibers, mono - and polycrystalline, any length;
f. Aromatic polyamide cellulose.
"Film integrated circuits" (3) - set of "scheme elements" and the metal connections formed by means of drawing thick or thin film on isolating "substrate".
Special note: "scheme element" - separate active or passive detail of the electronic scheme, such as one diode, transistor, resistor, condenser and so forth.
"Fixed" (5) - means that the algorithm of coding or compression cannot change the parameters set from the outside (for example, cryptographic parameters or parameters of key) and cannot be altered by the user.
"Group of optical sensors of management system flight" (7) - the network of the distributed optical sensors using beams of "laser", providing in real time these flight controls for processing onboard.
"Optimization of trajectory of flight" (7) - the procedure minimizing variations from four-dimensional (in space and time) required trajectory on the basis of maximization of characteristics or efficiency of accomplishment of task.
"Lattice of the focal plane" (6) - linear or two-dimensional planar lattice or combination of planar layers, separate elements detectors with the reading-out electronics or without it which works in the focal plane.
Special note: This determination does not turn on set of separate detectors or any two - three - or four-element detectors on condition of lack of transactions of introduction of temporary delay and integration in these elements.
"Relative width of strip of frequencies" (3) - the "instant width the" of strip of frequencies divided into average frequency bearing, expressed as a percentage.
"Spasmodic reorganization of frequency" (5) - form of "expansion of range" in case of which transmission frequency of separate communication channel is reconstructed by means of the accidental or pseudorandom sequence of discrete jumps.
"Time of switching of frequency" (3rd 5) - the maximum time (for example, delays) which is required to output signal when switching from one frequency to another for achievement of any of the following characteristics:
a. Frequencies within 100 Hz from its final value; or
b. Level within 1 dB from the level of final value.
"Synthesizer of frequencies" (3) - any kind of the generator of signal or source of the frequencies providing irrespective of the used generation method set of one or several at the same time or alternately generated signals purposefully taken or synchronized by means of smaller number of standards of the frequency (setting frequencies).
"Completely Autonomous Electronic and Digital Controller of the Engine" ("CAEDCE") (7,9) - the electronic management system the turbine engine or the engine of the combined cycle with use of the digital COMPUTER for management of variable parameters regulating draft of the engine or level of the output capacity removed from shaft in criteria range of operation of the engine from the beginning of regulation of fuel consumption before the end of its giving.
"Gas spraying" (1) - process of spraying of stream of the melted metal alloy on drops with a diameter of 500 microns or less in gas stream of high pressure.
"Space distributed" (6) - location of one object is removed from location any other more than on 1 500 m in any direction. Mobile sensors are always considered "territorially dispersed (geographically distributed)".
"Systems of targeting" (7) - systems which combine process of measurement and calculation of provision and speed of vehicles (navigation), with calculation and sending of teams to flight management systems for adjustment of their trajectory.
"Hot isostatic modification" (2) - process of pressing of the cast forms at temperatures over 375 To (102 0 C in hermetic amount through different circles (gaseous, liquid, solid particles, etc.) for creation of equal forces in all directions for decrease or elimination of internal cavities in the cast forms.
"The hybrid COMPUTER" (4) - the equipment designed to perform all following functions:
a. Accept data;
b. Process data, both in analog, and in digital representations; and
c. Provide data output.
"The hybrid integrated circuit" (3) - any combination of integrated circuits or the integrated circuit with "scheme elements" or the "discrete components" connected together for accomplishment of certain functions and having all following characteristics:
a. Containing, at least, one packageless device;
b. Components unite with each other with use of typical production methods of integrated circuits;
c. Their whole is replaced; and
d. He is subject to disassembly in the normal state.
Special note 1: "Scheme element" - separate active or passive detail of the electronic scheme, such as one diode, transistor, resistor, condenser and so forth.
Special note 2: "Discrete component" - "scheme element" in the separate case with own external conclusions.
"Quality improvement" (4) - processing of the images bearing information by means of such algorithms as compression in time, filtering, assessment of parameters, selection, correlation, rollup or transformations between the different fields of representation (for example, Fourier or Volsh's bystry transformation). Such processing does not include algorithms with use only of linear transformation or rotation of the separate image, such as shift, extraction of signs, registration or video effect like "false color".
"Immunotoxins" (1) - the conjugant of one-celled monoklokalny antibodies and "toxins" or "subtoxins" which is selectively influencing sick cells.
"In the public sphere" - means "technology" or "software" on which further distribution restrictions are not imposed. (the restrictions connected with copyright do not remove "technology" or "software" from category of "public").
"Information security" (the 4th 5) - all means and functions providing availability, confidentiality or integrity of information or communication excepting the means and functions protecting from defects. It includes "cryptography", "cryptanalysis", protection against own radiation and protection of the computer.
Special note: "cryptanalysis" - the analysis of cryptographic system or its entrance and output signals for the purpose of extraction of confidential parameters or sensitive information, including the clear text.
"Instant width of strip of frequencies" (3 5 7) - bandwidth in which power level of output signal remains to constants within 3 decibels without fine tuning of the key working parameters.
"Tool range" (6) - unambiguously determined range of operation of the radar.
"Isolation" (9) it is applied to components of rocket engines, that is, the case, nozzle, air inlets, case caps, and includes plates of the vulcanized or semi-vulcanized rubber mix with content of insulating and fire-resistant material. Can also include protective isolation or laying for removal of tension.
"The interconnected radar sensors" (6) - two or more radar sensors are considered interconnected if mutual exchange of information in real time takes place.
"Internal covering" (9) – it is applied to layer between solid rocket fuel and the case or insulating laying. Usually it is insulating or fire-resistant material on the basis of liquid polymer, for example, of uglerodonapolnenny polybutadiene with trailer hydroxylic groups (PKGG), or other polymer with the vulkanizatsionny additives sprayed or placed in the case.
"Internal magnetic градиометр" (6) - the separate element measuring gradient of magnetic field, and the related electronic block which output signal is measure of gradient of magnetic field.
Special note: See also "magnetic градиометр".
"The isolated live cultures" (1) - live cultures in inactive form and in the form of dry medicines include.
"Isostatic the press" (2) - the equipment capable to press in hermetic amount in different circles (gas, liquid, solid particles, etc.) for creation in this hermetic amount of equal pressure in all directions upon procurement or material.
"Laser" (0, 2, 3, 5, 6, 7, 8, 9) – set of components which create coherent both in space, and in time the light radiation strengthened by means of stimulated issue of radiation.
Special note: See also: "The chemical laser"; "Laser of ultrahigh capacity"; "The reconstructed laser".
"Linearity" (2) (it is usually measured through nonlinearity parameters) - the maximum variation of the valid characteristic (average according to indications of the upper and lower scale), positive or negative, from the straight line located so that to balance and minimize the maximum variations.
"Local network" (4) - the system of data transmission having all following characteristics:
a. Allowing any number of independent "information devices" to communicate directly with each other; and
b. Limited by geographical zone of the average sizes (for example, limits of the office building, plant, group of cases or storage facilities).
Special note: "The information device" means the equipment having capability to transfer or accept the sequences of digital data.
"Magnetic gradiyentometra" (6) - the devices intended for measurement of space changes of magnetic fields of the sources which are external in relation to this device. They consist of set of "magnetometers" and the corresponding electronic block at which exit the gradient of magnetic field is measured.
Special note: See also "internal magnetic gradiyentometra".
"Magnetometers" (6) - the devices intended for measurement of magnetic field of the sources which are external in relation to the device. Consist of separate measuring element of magnetic field and the related electronic block at which exit magnetic field is measured.
"Random access memory" (4) - the main storage location of data or teams for bystry access from the central processing unit. Consists of internal memory of "the digital computer" and any means of its hierarchical expansion, such as cache memory or expanded memory of parallel access.
"The materials resistant to corrosion of UF 6 (0)" - can be: copper, stainless steel, aluminum, aluminum oxide, aluminum alloys, the nickel or alloy containing 60% or is more than nickel (on weight) and the resistant to UF 6 fluorinated hydrocarbon polymers corresponding to separation process type.
"Matrix" (1 2 8th 9) - the strong continuous substance filled with particles, filamentary crystals or fibers.
"Measurement error" (2) - the characteristic parameter determining in what range about the measured value there is true value of the measured variable with probability of 95%. This size includes not compensated systematic variations, not compensated side play and accidental variations (see ISO 10360-2 or VDI/VDE 2617).
"Mechanical alloying" (1) - process of formation of alloy, resulting from binding, crushing and formations of new bonds between particles of powders of net metals and ligatures as a result of mechanical collisions. Nonmetallic particles of addition of the corresponding powders also can be entered into alloy.
"Fusion extraction" (1) - extraction process of "bystry hardening" and extraction of product in the form of tape or threads of alloy by means of introduction of short segment of the rotating cooled disk in bathtub with the melted metal alloy.
Special note: "Bystry hardening" - hardening of the melted material at speed, chillings more than 1 000 Fps.
"Spinningovaniye of fusion" (1) - process of "bystry hardening" of flow of the melted metal falling on the rotating cooled disk creating product in the form of wire, tape or particles in the form of scales or flakes.
Special note: "Bystry hardening" the process including material fusion hardening at the speeds of chilling exceeding 1 000 Fps.
"Microcomputer chip" (3) - the "monolithic integrated circuit" or "the multichip integrated circuit" containing the arithmetic-logic device (ALD) capable to execute commands of general purpose of the internal memory device in relation to the data containing in internal memory.
Special note: Internal memory can be expanded external memory.
"Microprocessor chip" (3) - the "monolithic integrated circuit" or "the multichip integrated circuit" containing the arithmetic-logic device (ALD) capable to carry out the sequences of teams of general purpose in external memory.
Special note 1: "The microprocessor chip" usually does not contain to the available user of random access memory though in case of accomplishment of logical function memory chip can be used.
Special note 2: This determination includes the installations of integral chip intended for functioning of "microprocessor chip".
"Microorganisms" (1 2) - bacteria, viruses, mycoplasma, rickettsiae, chlamydias or mushrooms, natural origin or changed, in the form of the isolated culture or as material, including nutrient medium which is purposely infected or contaminated by such cultures.
"Rockets" (1, 3, 6, 7, 9) – the complete missile systems and the unmanned aerial vehicle capable to deliver load weighing at least 500 kg to distance at least 300 km.
Monovolokno (1) or thread - the smallest component of fiber, usually several micrometers in the diameter.
"Monolithic integrated circuit" (3) - combination passive or active "elements of the scheme", which:
a. It is made by means of diffusion processes, processes of implantation or sedimentation inside or on surface of separate piece of semi-conductor material, so-called "chips (chip)";
b. Can be considered as continuous connected; and
c. Can perform functions of the scheme.
Special note: "scheme element" - separate active or passive detail of the electronic scheme, such as one diode, transistor, resistor, condenser and so forth.
"Monospectral sensors of images" (6) - the sensors capable to obtain information on the image from one discrete spectral range.
"The multichip integrated circuit" (3) - two or more "monolithic integrated circuits" which are on general "substrate".
"Multistream processing" (4) - the "microprogram" or methods of architecture of the equipment allowing to perform at the same time processing of two or more sequences of data under control of one or more sequences of teams by means of such methods as:
a. Architecture with centralized management of data flow (SMD);
b. Architecture with parallel and centralized management of data flow (MSIMD);
c. Architecture with the data flow (MIMD) decentralized by management, including closely connected, close connected or poorly connected; or
d. Structuring arrays of elements of processing, including systolic arrays.
Special note: "Microprogram" - the sequence of the elementary teams containing in special memory which accomplishment is initiated by introduction of team in the command register.
"Multispectral sensors of images" (6) - the sensors capable to perform simultaneous or consecutive collection of video data from two and more discrete spectral ranges. Sensors which have more than twenty discrete spectral ranges are known as hyper spectral sensors of the image.
"Natural uranium" (0) - the uranium containing the mix of isotopes which is found under natural conditions.
"The controller of access to network" (4) - the physical interface of the distributed switching network. He uses the general circle functioning at identical "speed of digital transmission" with management (for example, control or detection bearing) transfer. Irrespective of any other he chooses packets of data or group of data (for example, IEEE 802) addressed to it. It is the block which can be built in the computer, or the telecommunication equipment for ensuring access to system.
"The neural COMPUTER" (4) - the computer designed or the computer characterized by capability of the equipment modified for imitation of behavior of neuron or set of neurons, for example, to modulate the weight and quantity of interconnection of set of computing components on the basis of the previous information.
"Noise level" (6) - the electric signal expressed through parameters of spectral density of noise. The ratio between the noise level and peak level of signal is expressed by formula S 2 pp = 8 N 0 (f 2 - f 1) where S pp - the peak level of signal (for example, in nanoteslas), N 0 - the spectral density of capacity [for example, (nanotesla) 2/Hz] and (f 2 - f 1) - strip of frequencies.
"Nuclear reactor" (0) - all objects which are inside or components which usually are in direct contact attached to the reactor case, the equipment which manages energy level in active zone and or manage cooling agent of the first contour of active zone of the reactor.
"Numerical control" (2) - the automatic control of process exercised of the device using the numerical data which are usually entered in process of process course (source - ISO 2382).
"Object code" (9) - the form of suitable representation of one or more processes (the text of the program or language of the program) which is subject to execution which is transformed by programming system.
"Optical strengthening" (5) (in optical communication) - method of strengthening of the optical signals connected by separate optical source without transformation to electric signals, for example, using semiconductor optical amplifiers, fiber-optical luminescent amplifiers.
"The optical COMPUTER" (4) - the equipment designed or modified for the purpose of use of light for data presentation elements of computing logic by which are based on directly connected optical devices.
"The optical integrated circuit" (3) - the monolithic integrated circuit or the hybrid integrated circuit containing one or more parts intended for work as photodetector or the photocathode or accomplishment of optical or electrooptical functions.
"Optical switching" (5) - routing or switching of signals in optical form without transformation to electric signals.
"The total density of current" (3) - the total number of amperes rounds in the solenoid (i.e. the amount of number of rounds increased by the maximum current of each round) divided into the total area of cross section of the solenoid (including superconducting rounds, metal matrix into which superconducting rounds, cover material, the channel of chilling and so on are put).
"State Party" (the 7th 9) are the state, being the participant of the Vassenaarsky Arrangement. (See www.wassenaar.org)
"Peak capacity" (6) - energy of impulse in joules, divided into impulse duration in seconds.
"Personal smart card" (5) - the smart card contains chip which is programmed for certain application and cannot be reprogrammed by the user for any other application.
"Capacity management" (7) - measurement of capacity of the signal transmitted by the altitude indicator so that capacity of the accepted signal at height of "aircraft" is always maintained at the minimum level required for determination of height.
"Pressure sensors" (2) - devices for transformation of measurements of pressure to electric signal.
"Preliminary separation" (0 1) - application of any process for the purpose of increase in concentration of controlled isotope.
"Direct control of flight" (7) - stabilization of the aircraft or maneuvering by power sources (impulse), for example, the aerodynamic managed planes, or change of vector of draft.
"Basic element" (4), it is similar applied in Category 4 - this "element" is the basic in that case when the cost of its replacement constitutes 35% of total price of system to which the element belongs. At the price of element the price paid for it by the producer of system or the collector of system is considered. The total price is the normal international price in production site or picking of deliveries.
"Production" - includes all stages: designing, production technology, production, implementation, assembly (installation), check, testing, quality assurance.
"Production equipment" (1, 7, 9) – tools, samples, tightening devices, mandrels, rollers, dies, fittings, mechanisms for adjustment, the equipment for testing, other equipment and components for it, specially developed or modified for "development" or for one or more stages "productions".
"Production installations" (7, 9) – "production equipment" and the software which is specially developed for it established in the course of installation for "development" or for one or more stages "productions".
"Program" (the 2nd 6) - the sequence of teams for accomplishment or transformation to the form which is subject to execution by the computer.
"Compression of impulse" (6) - the coding and processing of signal of radar station of big duration transforming it to signal of small duration with preserving benefits of high energy of impulse.
"The impulse duration" (6) - duration of impulse of studying of the laser measured on half from the complete duration of impulse.
"The laser with good quality modulation" (6) - "laser" in which energy accumulates in inversion of density of population or the optical resonator and then is radiated in the pulse mode.
"Radar station with the reconstructed frequency" (6) - any method changing according to the pseudorandom sequence the bearing frequency of the transmitter of radar station between impulses or groups of impulses to the size equal or the exceeding width of strip of frequencies of impulse.
"Expansion of range of radar station" (6) - any method of modulation for distribution of energy of the signal concentrated in rather narrow strip of frequencies, in wider strip of frequencies by means of application of methods of accidental or pseudorandom coding.
"Strip of frequencies in real time" (the 2nd 3) for dynamic analyzers of signals" - the broadest range of frequencies of signal which the analyzer can issue on the displaying or memory device without violation of continuity of the analysis of input information. For multichannel analyzers in case of assessment "strips of frequencies in real time" the configuration of the channel with the greatest value of this parameter shall be used.
"Processing in real time" (6,7) - data processing of the COMPUTER providing the necessary service level as function of the available resources during the guaranteed time of reaction of system irrespective of loading level in the conditions of excitement of system with external events.
"Required" (1 – 9) – in relation to "technology" means only that part of technology which allows to reach or exceed controlled levels, characteristics or functions. Such "required" "technology" can contain in different goods.
"Permission" (2) - the smallest increment of indications of the measuring device; in digital devices - younger bit (source: ANSI B-89.1.12).
"Robot" (2nd 8) - manipulator which can make movements continuously or between certain points, have measuring sensors and have all following characteristics:
a. Multifunctionality;
b. Establish capability in certain provision or orient material, details, tools or special devices by means of the recustomized movements in three-dimensional space;
c. Can manage three or more servo-drivers with the closed or opened contour, including step engines; and
d. Has "possibility of programming available to the user" by means of training method with storing or due to use of the computer which can be the programmable logical controller, that is without intermediate mechanical transactions.
Special note: The above-stated determination does not turn on the following devices:
1. The manipulators managed only manually or the cameraman;
2. Manipulators with the fixed sequence of transactions to which the automated moving devices operating according to mechanically fixed programmable types of movements belong. The program is mechanically limited to fixers, such as pins or cams. The sequence of movements and the choice of trajectories or corners cannot change or be replaced with mechanical, electronic or electric means;
3. Mechanically managed manipulators with the variable sequence of transactions to which the automated moving devices operating according to mechanically fixed programmable types of movements belong. The program is mechanically limited to the fixed, but reconstructed devices, such as pins or cams. The sequence of movements and the choice of trajectories or corners are variables within the established structure of the program. Changes or modifications of structure of the program (for example, changes of pins or change of cams) concerning movement on one or several coordinates are performed only by means of mechanical transactions;
4. Not the servoupravlyaemy manipulators with the variable sequence of actions relating to the automated moving devices functioning according to mechanically fixed programmable types of movements. The program is subject to changes, inconsistency of transactions changes only by means of binary signal from mechanically fixed electric devices or the reconstructed fixers;
5. The lifting devices with the receiver of punched cards which are among the manipulators working in the Cartesian system of coordinates, manufactured as integral part of vertical system of bunkers for storage of materials and intended for ensuring access to content of these bunkers for loading or unloading.
"Centrifugal spraying" (1) - process of transformation of flow or the melted metal which is in bathtub by means of centrifugal force in drops with a diameter of 500 microns or less.
"Rove / ровинги" (1) - sheaf (usually 12-120) approximately parallel "locks".
Special note: "Lock" - linking of "monofibres" (usually from above 200), located approximately in parallel.
"Beating" (2) - the radial shift for one turnover of the main spindle measured in the plane, perpendicular axis of spindle in measurement point on the external or internal surface of rotation (source - ISO 230/1-1986, paragraph 5. 61).
"Large-scale coefficient" (7) (gyroscope or the accelerometer) - the relation of change of output signal to change of the entrance measured signal. The large-scale coefficient is usually estimated as inclination of straight line which can be constructed by method of the smallest squares according to the data received in case of change of entrance signal within the set range.
"Establishment time" (3) - time which is required to output signal for achievement of level of half of bit from its final value when switching between any two levels of the converter.
"LSM" - is equivalent to "The laser of ultrahigh capacity".
"The analyzer of signals" (3) - the equipment intended for measurement and display of the main characteristics of single-frequency fashion of multifrequency signal.
"Processing of signal" (3, 4, 5, 6) - processing of the signals received from the outside bringing information by means of algorithms, such as compression in time, filtering, parameter assessment, selection, correlation, folding or transformation from one field of representation to another (for example, bystry transformation of Fourier or Volsh's transformation).
"Software" - set of one or more "programs" or "microprograms" which are written down on any kind of the carrier.
Special note: "Microprogram" - the sequence of the elementary teams which are stored in special memory which accomplishment is initiated by the starting team entered into the register of teams.
"Source code" (or initial language) (4, 6, 7, 9) - the corresponding representation of one or more processes which can be transformed by programming system to the form performed by the equipment ("object code" or object language).
"Spacecrafts" (7, 9) – active and passive companions and space probes.
"Suitable for application in space" (3, 6) - the equipment designed, manufactured and tested for compliance to special electric and mechanical requirements or requirements of operating conditions for application in case of start and expansion of the satellites or high-rise aircraft functioning at the heights of 100 km or more.
"The special split material" (0) are the " uranium enriched with isotopes 235 or 233" uranium-233, plutonium-239, or any other material containing the above.
"The specific module of elasticity" (0, 1, 9) is module of Jung in Pascals that is equivalent to N / кв.м, divided into specific weight in N / куб.м, measured at temperature (296 +/-2) To ((23 +/-2) to 0 C) and relative humidity (50 +/-5) %.
"Specific durability on stretching" (0, 1, 9) is extreme durability on stretching in Pascals that is equivalent to N/sq.m, divided into specific weight in N / куб.м, measured in case of ambient temperature (296 +/-2) To ((23 +/-2) to 0 C) and relative humidity (50 +/-5) %.
"High-speed tempering of drop" (1) - process of bystry hardening of the melted metal hitting against the cooled obstacle with formation of flocculent product.
Special note: "Bystry hardening" - the process including material fusion hardening at the speeds of chilling exceeding 1 000 Fps.
"Expansion of range" (5) - method by means of which energy in rather narrow-band communication channel extends on much wider energy range.
"Radar station with Expansion of range" (6) - see. "Expansion of range of radar station".
"Stability" (7) - the standard deviation (1 sigma) of fluctuations of some parameter of rather calibrated size measured in stable temperature conditions. It is expressed as function of time.
"The countries - (not) participants of the Convention on chemical weapon (CWC)" (1) - the states for which the Convention on prohibition of development, productions, accumulatings and use of chemical weapon did not become effective. (See www.opew.org)
"Managed by the built-in program" (2, 3, 8) - the method of management using the teams which are built in electronic memory which the processor can perform for management of any set functions.
Special note: The equipment can be "managed by the built-in program" irrespective of whether electronic memory outside of or in this equipment is located.
"Substrate" (3) - plate of the main material with structure of connections or without it on which or in which "discrete components" either integrated circuits, or that and others together can be placed.
Special note 1: "Discrete component" - "scheme element" in the separate case with own external conclusions.
Special note 2: "Scheme element" - separate active or passive detail of the electronic scheme, such as one diode, transistor, resistor, condenser and so forth.
"Procurements" (6) - the monolithic masses which sizes are suitable for production of optical elements, such as mirrors or optical windows of transparency.
"Toxin component" (1) - structurally and functionally allocated component of whole "toxin".
Supersplava (2, 9) - alloys on the basis of nickel, cobalt or iron which durability exceeds durability of any alloy of the AISI 300 series at temperature over 922 To (649 0 C) in intense operating conditions and the environment.
"Superconducting" (1, 3, 6, 8) (on the basis of effect of superconductivity) - the term belongs to materials, for example, to metals, alloys or connections which can lose completely electric resistance, for example, to have infinitely high electric conductivity and to bear big electric currents without Joule heating.
Special note: The "superconducting" condition of material individually is characterized by "the critical temperature", critical magnetic field which is function of temperature, and the critical density of current which is function, both magnetic field, and temperature.
"Laser of Ultrahigh Capacity" (LUC) (6) - the "laser" capable to radiate energy (general or partial) over 1 kJ during 50 ms or having continuous capacity more than 20 kW.
"Superplastic formation" (1, 2) - process of deformation with use of heating of the metals which are characterized by low values of coefficient of lengthening (less than 20%) in strength point in case of regular testing of the module of durability for stretching in the conditions of room temperature for the purpose of achievement of lengthening in case of efforts smaller values of the module of durability on stretching, at least, twice.
"Symmetric algorithm (5)" - the cryptographic algorithm using the same key both for enciphering, and for decoding.
Special note: "The symmetric algorithm" is usually applied to ensuring confidentiality of information.
"Trajectories of systems" (6) - processed correlated (synthesis of data of radar station on the purpose with line item of flight task) and updated data (reports) on airplane provision in flight represented to dispatchers of control center of air traffic.
"The COMPUTER with systolic matrix" (4) - the computer in which the data flow and their transformation can dynamically be controlled at the level of the logical scheme of the user.
"Tape" (1) - the material consisting of the alternating or unidirectional "monofibres", "locks", "roves", "cords" or "пряж", etc. which are previously impregnated with pitch.
Special note: "Lock" - linking of "monofibres" (usually from above 200), located approximately in parallel.
"Technology" - special information which is required for "development", "production" or "use" of the equipment. Information can take the form of "specifications" or "technical assistance".
Special note 1: "Technical assistance" can take such forms as instructing, acquisition of skills, training, production knowledge, consulting services. Technical assistance can include transfer of "specifications".
Special note 2: "Specifications" can take such forms as photocopies, plans, charts, models, formulas, tables, engineering designs and specifications, user's guides and instructions in hand-written type or written down on other carriers, such as disk, tape, ROM.
"The bending spindle" (2) - the spindle holding the tool which changes in processing angular provision of the central axis concerning other axes.
"Constant time" (6) - time which is required to light incentive in case of increase in current to reach level (1-1/a) from final value (i.e. 63% of final value).
"Superbroadband modulation on time" (5) - technology according to which very short radio-frequency impulses with precisely certain provision on time are modulated according to transmitted data by change of provisional regulations of impulses (usually called by pulse position modulation, IPM) which are canalized or perestanavlivatsya according to the IPM pseudorandom noise codes then are transferred and accepted directly in pulse type without use of the bearing frequencies therefore extremely low density of capacity in the ultra-wide frequency ranges turns out. This technology is known also as pulse radio (radio communication).
"General management by flight" (7) - automated management of variable parameters of "aircraft" and trajectory of its flight for the purpose of accomplishment of objective according to changes of data on tasks, damages or other "aircraft" in real time.
"General speed of digital transmission" (5) - the number of bits, including coding of the channel, redundancy and so forth, in unit of time, transferred between the corresponding equipment in system of digital transmission.
Special note: See also "the speed of digital transmission".
"Cord" - linking of the "monofibres" usually approximately parallel.
"Toxins" (1,2) is toxins in the form of purposely isolated medicines or mixes irrespective of the fact how they are made, different from the toxins which are pollutants of other materials such as, pathological samples, grain crops, foodstuff or seed fund of "microorganisms".
"The transitional laser" (6) - "laser" in which environment of generation is initiated by means of transition of energy in case of collisions of unexcited atom or molecule with the initiated atoms or molecules.
The "reconstructed" laser (6) - the "laser" capable to generate radiation on all lengths of waves in the range of several transitions of "laser". "Laser" with the choice of some line generates the radiation of discrete lengths of waves within one transition of "laser" and it is not considered reconstructed.
"The uranium enriched with isotopes 235 or 233" (0) - the uranium containing isotopes 235 or 233, or that and another together in such quantity that the relation of the amount of these isotopes to isotope 238 was more relation of isotope 235 to isotope 238 in natural uranium (isotope ratio of 0,72 of %).
"Application" means use, installation (including, installation on site of use), working capacity maintenance, check, repair, capital repairs and recovery;
"Programmability the user" (6) - availability of the equipment allowing the user to insert, modify or replace "programs" with other means than:
a. Physical change of connections or distributing; or
b. Establishment of control of functions, including control of the driven parameters.
"Vaccine" (1) - the medicine in pharmaceutical structure spread according to the license or has permission for release to the market or for use in clinical practice, received from regulating authorities or the country of the producer or the country of the user. Means is designed to stimulate immune reaction of organism of people or animals for prevention of diseases among imparted.
"Vacuum spraying" (1) - process of spraying of stream of fusion on drops with a diameter of 500 microns or less bystry release of the liquefied gas in case of effect of vacuum.
"Aerodynamic profiles with variable geometry" (7) - use of flaps either trimmers, or slats or hinged regulation of corner of nasal part which provision can be regulated in flight.
"Yarn" (1) - linking of the twisted "locks".
Special note: "Lock" - linking of "monofibres" (usually from above 200), located approximately in parallel.
"FADEC systems" (7, 9) (completely autonomous electronic and digital management systems the engine) – digital electronic management system gas turbine engines which can autonomous manage the engine throughout all operational range of the engine, as in normal, and in an emergency from the moment of its start to stop.
"Unmanned aerial vehicle" ("UAV") (9) – any aircraft capable to fly up and support controlled flight and air navigation without presence of the person onboard.
Products which are subject to control of specific goods during the exporting, re-export, transit and conversion of products out of the territory of the Republic of Kazakhstan
Category 0
Nuclear materials, installations and equipment 0A of System, equipment and components
0A001 "Nuclear reactors" and specially developed or prepared equipments and components, such, as:
a. The "nuclear reactors" capable to work in the mode of controlled self-sustaining chain reaction of division;
b. Specially developed or prepared metal cases assembled or their main parts of factory production for placement in them active zone of "nuclear reactors" and capable to maintain the working pressure of the heat carrier of the first contour;
c. Specially developed or prepared manipulyatorny equipment for loading or extraction of fuel from "nuclear reactors";
d. Specially developed or prepared cores for speed control of reaction in "nuclear reactors", supporting and suspended frameworks, drives and the directing pipes for cores;
e. Specially developed or prepared reactor pipes of high pressure for placement in them fuel elements and the heat carrier of the first contour in "nuclear reactors" with the working pressure exceeding MPa 5,1;
f. Specially developed or prepared zirconium pipes or assemblies of pipes from metal zirconium or its alloys for use in "nuclear reactors" in which the relation on hafnium weight to zirconium is less than 1:500;
g. Specially developed or prepared pumps for maintenance of circulation of the heat carrier of the first contour of "nuclear reactors";
h. Specially developed or prepared "internal parts of the reactor" for use in "nuclear reactor", such as the supporting columns of active zone directing pipes for the regulating cores, thermal screens, partitions, pipe lattices of active zone, diffuser plate;
Note: In 0A001.h "Internal part of the reactor" is the any main structure in the reactor case which is carrying out one or more functions, such as support of active zone, arrangement of fuel elements, the direction of the main flow of cooling agent, ensuring radiation protection of the case of the reactor and control of the equipment which is in active zone.
i. Specially developed or prepared heat exchangers (steam generators) for use in the first contour of "nuclear reactor";
j. Specially developed or prepared detectors of neutrons and measuring devices for determination of neutron flow in active zone of "nuclear reactor".
k) the "external thermal filters" which are specially designed or prepared for use in "nuclear reactor" for the purpose of decrease in loss of heat and also as protective cover for the reactor case.
Note: In 0A001k "external thermal filters" are the main structural elements established on the reactor case for the purpose of decrease in loss of heat of the reactor and temperature in protective cover.
0A001, and 8401 10 000 0
0A001, b 8401 40 000 0
0A001, with 8426 19 000 0
8426 99 900 0
0A001, d 8401 40 000 0
0A001, е 7304
7507 12 000 0
7608 20
8109 90 000 0
8401 40 000 0
0A001, f 8109 90 000 0
0A001, g 8413 81 000 9
0A001, h 8401 40 000 0
0A001, i 8419 50 000 0 (except intended for civil aviation)
8404 20 000 0
8402 19 900 9
0A001, j 9030 10 000 0
0A001, k 8401
0В Test, control and production equipment
0В001 Installations for separation of isotopes of "natural uranium", "depleted uranium" and "the special split materials", and specially developed or prepared for this purpose equipment and components, such, as:
a. Specially developed installations for separation of isotopes of "natural uranium", "depleted uranium" and "the special split materials", such, as:
1. Gas centrifuges;
2. Gas-diffusion barriers;
3. Installations of aerodynamic enrichment;
4. Installations of chemical exchange;
5. Installations of ionic exchange;
6. Installations for "laser separation" of isotopes by method of atomic vapors (AVLIS);
7. Installations for "laser separation" of isotopes by molecular method (MLIS);
8. Installations of plasma separation;
9. Installations of electromagnetic separation;
b. Specially developed or prepared gas centrifuges, nodes and components for use in gas centrifuges, as:
Note: "the material having high value of the relation of durability to density" means any of the following:
a) Maraging became, 2 050 MRA having the maximum strength on gap or more;
b) The aluminum alloys having the maximum strength on gap of 460 MRA or more; or
c) The "Fibrous materials" suitable for use in "composition" structures and the having "values of the specific module" it is more than 3, 18 x 10 (6) m and "the maximum strength" on gap bigger, than 76, 2 x 10 (3) m.
1. Gas centrifuges;
2. Complete rotor assemblies;
3. Cylinders of rotor pipes with thickness of wall of 12 mm or less, with a diameter from 75 mm to 400 mm, made of one or more materials having "high value of the relation of durability to density";
4. Rings or bellow valves with thickness of wall of 3 mm or less, with a diameter from 75 mm to 400 mm, intended for support of rotor pipe or connection of rotor pipes and made of one of the materials having "high value of the relation of durability to density";
5. The partitions with a diameter from 75 mm to 400 mm for installation in rotor pipe of the centrifuge made of one of materials, "having high value of the relation of durability to density";
6. The upper/lower covers with a diameter from 75 mm to 400 mm precisely corresponding to diameter of the ends of rotor pipe made of one of the materials having "high value of the relation of durability to density";
7. The bearings with magnetic suspension bracket consisting of the ring magnet suspended in the holder containing the damping circle. The holder is made of "material, corrosion-resistant to UF6" or is protected by covering from such materials. The magnet unites with the polar tip or the second magnet established on the upper cover of rotor;
8. Specially prepared bearings containing the node axis / sealing ring mounted on damper;
9. The molecular pumps including cylinders with the spiral ditches turned or squeezed out inside and with the openings drilled inside;
10. Stators of ring form for high-speed multiphase hysteresis (or reactive) electric motors of alternating current for synchronous work in the conditions of vacuum in the range of the frequencies of 600-2000 Hz and in power range 50-1000 BA.;
11. Centrifuge cases/receivers for placement of assembly of rotor pipe of the gas centrifuge in them. The case consists of the tough cylinder with wall thickness to 30 mm with pretsizionno the processed ends for installation of bearings. Cases are manufactured of "materials, corrosion-resistant to UF6" or is protected by covering from such materials;
12. The traps consisting of tube with internal diameter up to 12 mm for extraction of UF6 gas from rotor pipe by method of tube of Pitot. Tubes are made of "materials, corrosion-resistant to UF6" or are protected by covering from such materials;
13. Specially developed or prepared frequency converters (converters or inverters) and their components for power supply of stators of engines for gas centrifuges having full range of the following characteristics:
a) Multiphase exit in the range from 600 to 2 000 Hz;
b) Stabilization of frequency is better, than % 0,1;
c) Low linear misstatement smaller, than 2%; and
d) The efficiency is more than 80%;
page. Specially developed or prepared assemblies and components for use in case of gas-diffusion enrichment:
1. The gas-diffusion barriers made from porous metal, polymeric or ceramic "material, corrosion-resistant to UF 6" with size of time from 10 to 100 mm, 5 mm thick or it is less, and for tubular forms - with a diameter of 25 mm or it is less;
2. The cameras of diffusers manufactured of "material, corrosion-resistant to UF6" or protected by covering from such materials;
3. Compressors (with positive shift, centrifugal and axial type) or gas blowers with productivity on entrance of 1 cubic m/min or more UF6 and with pressure at the exit to 666,7 of kPa, made of "material, corrosion-resistant to UF6" or protected by covering from such materials;
4. Consolidations of the rotating shaft for the compressors or gas blowers specified in 0v001.s.z. Such consolidations are usually projected on the speed of natekaniye of buffer gas less than 1 000 cubic cm/min.;
5. The heat exchangers manufactured of aluminum, copper, nickel or alloys containing more than 60 percent of nickel, or from their combination, or covered with them, designed for work with pressure are lower atmospheric and the changes of pressure determining leakage, less than 10 Pas an hour in case of pressure difference of 100 kPa providing speed;
6. The valves of bellows-sealed type manufactured of "material, corrosion-resistant to UF6" or protected by covering from such materials, with a diameter from 40 to 1 500 mm;
d. Specially developed or prepared equipments and components for use on installations of aerodynamic enrichment, as:
1. The dividing nozzles consisting of slit-like curved channels with radius of bend less than 1 mm, made of "material, corrosion-resistant to UF 6", and having the internal cutting edge which divides the gas proceeding through nozzle into two fractions;
2. The vortex tubes having the cylindrical or cone-shaped form, made of "material, corrosion-resistant to UF6", or protected by covering from such materials and having diameter from cm 0,5 to 4 cm in case of length relation to diameter 20:1 or less and also one or more tangential entrance opening;
3. Compressors and gas blowers (with positive shift, centrifugal and axial type) made of "material, corrosion-resistant to UF6", or protected by covering from such materials, performance on entrance of 2 cubic m/min., and consolidations of the rotating shaft for them;
4. The heat exchangers manufactured of "materials, corrosion-resistant to UF6", or protected by covering from such materials;
5. The casings of the dividing elements made of "materials, corrosion-resistant to UF6", or protected by covering from such materials for the room in them vortex tubes or dividing snuffled;
6. The valves of bellows-sealed type manufactured of "materials, corrosion-resistant to UF6" or protected by covering from such materials, with a diameter from 40 to 1 500 mm;
7. The systems intended for allocation of UF6 from the bearing gas (hydrogen or helium) to one part on one million or less and able to turn on such equipment as:
a. The cryogenic heat exchangers and cryoseparators capable to create temperatures 153 K (-120 0 C) or less;
b. The blocks of cryogenic chilling capable to create temperatures 153 K (-120 0 C) or less;
c. Blocks of dividing snuffled or vortex tubes for allocation of UF6 from the bearing gas;
d. Cold traps of UF6, capable to create temperatures 253 K (-20 0 C) or less;
e. Specially developed or prepared equipments and components for use on installations of chemical enrichment, such, as:
1. Liquid and liquid pulse exchange columns. For corrosion stability to the concentrated solutions of hydrochloric acid these columns and their internal components are made of suitable plastic materials (such as the fluorinated hydrocarbon polymers or glasses) or protected by covering from such materials. Columns are designed on short (30 with or less) passing time in the cascade;
2. Liquid and liquid centrifugal contact filters. For corrosion stability to the concentrated solutions of hydrochloric acid these contact filters and their internal components are manufactured of suitable plastic materials (such as the fluorinated hydrocarbon polymers or glasses) or protected by covering from such materials. Contact filters are designed on short (30 with or less) passing time in the cascade;
3. Cells of electrochemical recovery for recovery of uranium from one valence state in another. Materials of cells shall be corrosion-resistant to the concentrated solutions of hydrochloric acid;
4. The power supply systems of cells of electrochemical recovery consisting of the equipment of extraction by the solvent for extraction of U+4 from organic flow. Those parts of the equipment of system which are in contact with technological flow shall be made of the corresponding materials (such as glass, the fluorinated hydrocarbon polymers, polyphenyl sulfate, sulphone of polyether and the graphite impregnated with pitch) or are protected by covering from such materials;
5. The systems of preparation of food for production of nutritious solutions of uranium chloride of high purity consisting of the equipment for dissolution, extraction by the solvent and (or) the ion-exchange equipment for cleaning, and also electrolytic cells for recovery of U+6 or U+4 in U+3;
6. Systems of oxidation of uranium for oxidation of U+3 in U+4;
f. Specially developed or prepared equipments and components for use on installations of ion-exchange enrichment, such, as:
1. Quick-response ion-exchange pitches / absorbents, including porous pitches of macromesh structure and (or) membrane structures in which active groups of chemical exchange are limited to covering on surface of inactive porous auxiliary structure, and other composition structures in any acceptable form, including particles or fibers. These ion-exchange pitches / absorbents have diameter of 0,2 of mm or less and shall be chemically resistant in relation to the concentrated solutions of hydrochloric acid. Pitches/absorbents are specially intended for receipt of kinetics of very bystry exchange of isotopes of uranium (semi-exchange duration less than 10 c) and have potential to work at temperature in the range from 373 K (100 0 C) to 473 K (200 0 C);
2. Ion-exchange columns more than 1 000 mm, (cylindrical) with diameter. These columns are made of materials (such as titanium or the fluorinated hydrocarbon polymers), resistant to the corrosion caused by the concentrated solutions of hydrochloric acid or protected by covering from such materials, and are capable to work at temperature in the range from 373 K (100 0 C) to 473 K (200 0 C) and pressure above MPa 0,7;
3. Ion-exchange systems of reflux (chemical or electrochemical oxidation or recovery) for regeneration of reagent(s) of the chemical recovery or oxidation used in cascades of ion-exchange uranium enrichment;
g. Specially developed or prepared equipments and components for use in enrichment installations for process of "laser" separation of isotopes by method of atomic vapors (AVLIS), such, as:
1. Highly powerful strip or raster electron beam guns with the transferred capacity on target of more 2,5 of kW/cm for use in systems of evaporation of uranium;
2. The systems for processing of the liquid melted uranium or liquid uranium alloys consisting of crucibles and the cooling equipment for crucibles. Crucibles and other components of this system are made of corrosion-resistant and heat-resistant materials, or protected by covering from such materials (for example, the tantalum covered with yttrium oxide graphite, the graphite covered with oxides of other rare-earth elements or their structures);
Special note: See also 2A225.
3. Aggregates for collection of "product" and "tails". Components for these aggregates are made of the materials resistant to heating and the corrosion caused by vapors of metal uranium or liquid uranium or protected by covering from these materials such as the graphite covered with yttrium oxide or tantalum;
4. Casings of the dividing module (cylindrical or rectangular cameras) for the room of source of vapors of metal uranium in them, the electron beam gun and collectors of "product" and "tails";
5. "Lasers" or "laser" systems for separation of isotopes of uranium with the range frequency stabilizer for work during the long periods of time;
Special note: See also 6A005 and 6A205.
h. Specially developed or prepared equipments and components for use in enrichment installations of molecular "laser" separation of isotopes (MLIS) or chemical reaction by means of the selective on isotopes of laser activation (CRISLA), such, as:
1. Broad supersonic nozzles for chilling of the mixes UF 6 and the bearing gas to 150 K (-123 0 C) or below and made of "materials, corrosion-resistant to UF 6";
2. Collectors of product of pentafluorated uranium (the UF5) consisting of the filter, collectors of shock or cyclonic type or their combinations and made of "materials, corrosion-resistant to UF5/UF6";
3. The compressors manufactured of "materials, corrosion-resistant to UF6", or protected by covering from such materials, and consolidations of the rotating shaft for them;
4. The equipment for fluoration of UF5 (in firm condition) in UF6 (gas);
5. Systems for department UF6 from the bearing gas (nitrogen, argon or other gas can be the bearing gas), including:
a. The cryogenic heat exchangers and cryoseparators capable to create temperatures 153 K (-120 0 C) or below;
b. The blocks of cryogenic chilling capable to create temperatures 153 K (-120 0 C) or below;
c. Cold traps of UF6, capable to create temperatures 253 K (-20 0 C) or below;
6. "Lasers" or "laser" systems for separation of isotopes of uranium with the stabilizer are frequent range for work during the long periods of time;
Special note: See also 6A005 and 6A205
i. Specially developed or prepared equipments and components for use on enrichment installations with plasma separation, such, as:
1. Microwave power sources and antennas for generation or acceleration of ions and having the following characteristics: frequency is higher than 30 GHz and average output capacity for formation of ions more than 50 kW;
2. Solenoids for radio-frequency excitement of ions in the range of frequencies over 100 kHz and capable to work in case of average capacity more than 40 kW;
3. Production systems of uranium plasma.
4. The systems for processing of the liquid melted uranium or liquid uranium alloys consisting of crucibles and the cooling equipment for crucibles. Crucibles and other components of this system are made of corrosion-resistant and heat-resistant materials or protected by covering from such materials. Acceptable materials include the tantalum covered with yttrium oxide graphite, the graphite covered with oxides of other rare-earth elements or their structures;
Special note: See also 2A225.
5. Aggregates for collection of "product" and "tails". These aggregates are manufactured of the materials resistant to heating and the corrosion caused by vapors of metal uranium such as the graphite covered with yttrium oxide or tantalum, or protected by covering from such materials;
6. Casings of the dividing module (cylindrical) for the room of source of uranium plasma in them, the energy solenoid of radio frequency and collectors of "product" and "tails", made of the corresponding non-magnetic materials (for example, stainless steel);
j. Specially developed or prepared equipments and components for use on installations of electromagnetic enrichment, such, as:
1. The separate or numerous sources of ions of uranium consisting of source of vapor, the accelerator ionizer, made of the corresponding non-magnetic materials (as graphite, stainless steel or copper) and capable to provide general current in bunch of ions of 50 m And or more;
2. The plates receivers of ions having two or more cracks and the groove, for collection of bunches of ions enriched and depleted uranium and made of the corresponding non-magnetic materials (such as graphite or stainless steel);
3. The vacuum casings for electromagnetic separators of uranium made non-magnetic materials (for example, stainless steel) and the Pas intended for work with pressure of 0,1 or below;
4. The magnetic polar tips having diameter more than 2 m;
5. The high-voltage power supplies for sources of ions having all following characteristics:
a. Can work in the continuous mode;
b. Output voltage is 20 000 V or more;
c. Output current 1 A or more; and
d. Stabilization of tension is better, than % 0,01 within 8 hours;
Special note: See also 3A227.
6. Power supplies for magnets (high capacity, direct current) having all following characteristics:
a. Can work in the continuous mode with output current 500 A or more at voltage of 100 of V or more; and
b. Stabilization of current or tension is better, than % 0,01 within 8 hours.
Special note: See also 3A226
0B001 and. 1. 8401 20 000 0
0B001 and. 2. 8401 20 000 0
8421 39
0B001 and. 3. 8401 20 000 0
0B001 and. 4. 8401 20 000 0
0B001 a. 5. 8421 29 000 9
0B001 a. 6. 8401 20 000 0
9013 20 000 0
0B001 a. 7. 8401 20 000 0
9013 20 000 0
0B001 a. 8. 8401 20 000 0
0B001 a. 9. 8401 20 000 0
0B001 b. 1. 8401 20 000 0
0B001 b. 2. 8401 20 000 0
0B001 b. 3. 8401 20 000 0
0B001 b. 4. 8307
8401 20 000 0
0B001 b. 5. 8401 20 000 0
0B001 b. 6. 8401 20 000 0
0B001 b. 7. 8483 30 800 9
0B001 b. 8. 8483 30 800 9
0B001 b. 9. 8414 10 250 0
0B001 b. 10. 8503 00 990 0
0B001 b. 11. 8401 20 000 0
0B001 b. 12. 8401 20 000 0
0B001 b. 13. 8504 40
8502 40 000 0
0B001 of page 1. 8401 20 000 0
8421 39
0B001 with. 2. 7310 10 000 0
7508 90 000 0
7611
7612
0B001 of page 3. 8414 80 (except 8414 80 110 1, 8414 80 190 1,
8414 80 220 1, 8414 80 280 1, 8414 80 510 1,
8414 80 750 1, 8414 80 780 1, 8414 80 800 1)
0B001 of page 4. 8484 10 000 0 (except, intended for
civil aviation)
8484 90 000 0 (except, intended for
civil aviation)
8487 90 800 0
0B001 of page 5. 8419 50 000 0 (except, intended for
civil aviation)
0B001 of page 6. 8481 10
8481 30 910 0
8481 30 990 0
8481 80
0B001 d. 1. 8401 20 000 0
0B001 d. 2. 8401 20 000 0
0B001 d. 3. 8414 80
0B001 d. 4. 8419 50 000 0 (except, intended for
civil aviation)
0B001 d. 5. 8401 20 000 0
0B001 d. 6. 8481 10
8481 30 910 0
8481 30 990 0
8481 80
0B001 d. 7. 8419 50 000 0 (except, intended for
civil aviation)
0B001 e. 1. 8401 20 000 0
0B001 e. 2. 8401 20 000 0
0B001 e. 3. 8401 20 000 0
0B001 e. 4. 8401 20 000 0
0B001 e. 5. 8401 20 000 0
0B001 e. 6. 8401 20 000 0
0B001 f. 1. 3824 90 900 0 (only ionites)
3914 00 000 0
0B001 f. 2. 8421 29 000 9
0B001 f. 3. 8401 20 000 0
0B001 g. 1. 8401 20 000 0
0B001 g. 2. 8401 20 000 0
0B001 g. 3. 8419 89 989 0
8486 10 000 9
8486 20 900 9
8486 30 900 9
8486 40 000 9
0B001 g. 4. 8401 20 000 0
0B001 g. 5. 8401 20 000 0
9013 20 000 0
0B001 h. 1. 8401 20 000 0
0B001 h. 2. 8401 20 000 0
0B001 h. 3. 8414 80 (except 8414 80 110 1, 8414 80 190 1,
8414 80 220 1, 8414 80 280 1, 8414 80 510 1,
8414 80 750 1, 8414 80 780 1, 8414 80 800 1)
0B001 h. 4. 8401 20 000 0
0B001 h. 5. 8419 50 000 0 (except, intended for
civil aviation)
0B001 h. 6. 8401 20 000 0
9013 20 000 0
0B001 i. 1. 8543 10 000 0
0B001 i. 2. 8504 50 950 0
0B001 i. 3. 8401 20 000 0
0B001 i. 4. 8401 20 000 0
0B001 i. 5. 8419 89 989 0
8486 10 000 9
8486 20 900 9
8486 30 900 9
8486 40 000 9
0B001 i. 6. 8401 20 000 0
0B001 j. 1. 8401 30 000 0
0B001 j. 2. 8401 20 000 0
0B001 j. 3. 8401 20 000 0
0B001 j. 4. 8505 90 100 0
0B001 j. 5. 8504 40 880 9
0B001 j. 6. 8504 40 880 9
0B002 The special and developed or prepared auxiliary systems, the equipment and components, for installations of separation of the isotopes specified in 0B001, made of "materials, corrosion-resistant to UF 6", or protected by covering from such materials, such, as:
a. The autoclaves, thermostats or systems used for giving of UF 6 to the place of enrichment;
b. Desublimatora or the cold traps used for removal of heated UF6 from process of enrichment for the subsequent movement;
c. The stations of "products" and "tails" used for withdrawal of UF6 in containers;
d. The installations of liquefaction or hardening used for removal of UF6 from process of enrichment by compression, chilling and transfer of UF6 in liquid or firm state;
e. Specially developed or prepared systems of pipelines and collectors for deduction of UF6 in diffusion, centrifugal or aerodynamic cascades;
Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info
Database include more 50000 documents. You can find needed documents using search system. For effective work you can mix any on documents parameters: country, documents type, date range, teams or tags.
More about search system
If you cannot find the required document, or you do not know where to begin, go to Help section.
In this section, we’ve tried to describe in detail the features and capabilities of the system, as well as the most effective techniques for working with the database.
You also may open the section Frequently asked questions. This section provides answers to questions set by users.