Document from CIS Legislation database © 2003-2022 SojuzPravoInform LLC

ORDER OF THE GOVERNMENT OF THE RUSSIAN FEDERATION

of July 16, 2022 No. 1286

About the approval of the list of the equipment and materials of dual purpose and appropriate technologies applied in the nuclear purposes concerning which export control is exercised

According to article 8 of the Federal law "About Export Control" Government of the Russian Federation decides:

1. Approve the enclosed list of the equipment and the materials of dual purpose and appropriate technologies applied in the nuclear purposes concerning which export control is exercised.

2. This resolution becomes effective from the date of its official publication.

Russian Prime Minister

M. Mishustin

Approved by the Order of the Government of the Russian Federation of July 16, 2022, No. 1286

The list of the equipment and the materials of dual purpose and appropriate technologies applied in the nuclear purposes concerning which export control is exercised

 

Item No.

Name <*>

Code of the CN FEA EEU <*>

Section 1. Industrial equipment

1.1.

Equipment, components and components

1.1.1.

High density (from lead glass or from other materials) the windows of radiation protection having everything the following characteristics, and specially developed frames for them:

a) the area on "cold surface" of more 0,09 of sq.m;

b) density is over 3 g / cubic cm; and c) thickness of 100 mm or more

7003 19;

7005 29 800 0;

7006 00;

9022 90 000 0

Technical note.

In Item 1.1.1 the term "cold surface" means the visible surface of window subject to the smallest radiation level, according to constructional application

1.1.2.

Radiation resistant TV cameras or lenses for them, specially developed or the normalized as radiation resistant to maintain general dose of radiation more than 5 x 104 Heat (silicon) without deterioration in work characteristics

8525 82 110 0;

8525 82 190 0;

8540 20 100 0;

9002 19 000 0

Technical note.

The term "Gray (Silicon)" provided in Items 1.1.2 and 1.1.3. 1, treats the energy expressed in joules on kilogram which was absorbed by unscreened silicon sample on exposure by the ionizing radiation

1.1.3.

Robots, working bodies and controllers, such, as:

1.1.3.1.

The robots or working bodies having any of the following characteristics:

a) specially developed according to national standards of safety for works with powerful explosives in the explosive environment (for example, to satisfying restrictions for parameters of the electrical accessories intended for work with explosives in the explosive environment); or

b) specially developed or estimated as radiation resistant to maintain general dose of radiation more than 5 x 104 Heat (silicon) without deterioration in work characteristics

8428 70 000 9;

8428 90 800 0;

8479 50 000 0

1.1.3.2.

Specially developed controllers for any robots or working bodies specified in Item 1.1.3.1

8537 10 100 0;

8537 10 910 0;

8537 10 980 0;

8541 51 000 0;

8541 59 000 0

Note.

On Item 1.1.3 the robots which are specially designed for non-nuclear industrial application, such as, for example, used in painting cameras for cars are not subject to export control

Technical notes:

1. In Item 1.1.3 the term "robot" means the manipulator which can continuously move or bucketed, can use sensors and has all following characteristics:

a) is the multi-function printer;

b) it is capable to establish or orient material, details, tools or special devices by means of different movements in three-dimensional space;

c) includes three or more servoustroystvo with the closed or opened contour which can include step engines; and

d) has programmability, to the available user by means of method of training/reproduction or by means of the COMPUTER which can be the programmable logical controller, that is without mechanical intervention

Special notes:

1. In the above-stated technical notes the term "sensors" means detectors of the physical phenomenon which output signal (after transformation to signal which can be deciphered by the controller) is capable to generate programs or to modify program teams or numerical program data. This concept turns on sensors with machine sight, infrared or acoustic display, the touch probe, measurement of domestic situation, optical or acoustic measurement of distances or with opportunities of measurements of efforts or the rotary moment

2. In the above-stated technical notes the term "programmability available to the user" means the means allowing the user to insert, modify or replace programs by means of means which are excellent from:

a) physical change of the electric circuit or interrelation of electric systems; or

b) establishments of the functional management including input of parameters

3. The above-stated determination does not turn on the following devices:

a) the manipulators managed only manually or the cameraman;

b) manipulators with the fixed sequence of actions which are the automatic moving devices operating according to mechanically fixed programmed movements. The program is mechanically limited to motionless fixers, such as pins or cams. The sequence of movements and the choice of the directions or corners do not change or change mechanical, electronic or electric means;

c) mechanically managed manipulators with the variable sequence of actions which are automatically the moving devices operating according to mechanically fixed programmed movements.

The program is mechanically limited fixed, but regulated emphasis, such as pins or cams. The sequence of movements and the choice of the directions or corners can change within the set program model. Variations or modifications of program model (for example, change of pins or cams) on one or several coordinates of movement are carried out only by means of mechanical transactions;

d) neservoupravlyaemy manipulators with the variable sequence of actions which are automatically the moving devices operating according to mechanically fixed programmed movements. The program can change, but the sequence of teams renews only by means of binary signal from mechanically fixed electric binary devices or regulated limiters;

e) the cranes pilers determined as the systems/manipulators working in the Cartesian coordinates, manufactured as components of vertical system of warehouse bunkers and designed to provide warehousing and unloading of content of these bunkers

4. In Item 1.1.3 the term "working bodies" means clips, active means of machining and any other tools which join the basis on the end of "hand" of the manipulator of the robot

Special note.

In the above-stated determination the term "active means of machining" is understood as devices for transfer to the processed detail of motion energy, processing or indication of the direction

1.1.4.

Remote manipulators which can be used for ensuring remote actions in transactions of radiochemical separation or in hot cameras, having any of the following characteristics:

a) capable to transfer actions of the operator through wall of the hot camera by thickness of 0,6 of m or more (transaction "through wall"); or

b) capable to transmit actions of the operator through cover of the hot camera by thickness of 0,6 of m or more (transaction "through cover")

8428 70 000 9;

8428 90 800 0

Technical note.

Remote manipulators provide transfer of actions of the person operator to remotely operating "hand" and the terminal fixer. Manipulators can be the owner/servant type (the manipulators copying movements of the operator) or to be controlled the handle of management or the keyboard

1.2.

Test and production equipment

1.2.1.

Machines for rotational expression (extract), the obkatny milling machines capable to perform functions of rotational expression (extract), and mandrels, such as:

1.2.1.1.

The machines having both following characteristics:

a) rub or is shakier (active or directing); and

b) which according to the technical specification of the manufacturer can be equipped with blocks of the numerical control (NC) or computer management

8462 25 000 0;

8462 69 001 2;

8462 69 001 3;

8462 90 001 2;

8462 90 001 3;

8463 90 000 0

Note.

Item 1.2.1.1 turns on also the machines having only one roll intended for metal deformation and two auxiliary rolls which support mandrel, but do not participate directly in deformation process

1.2.1.2.

Rotor обкатные the mandrels developed for forming of cylindrical rotors with internal diameter from 75 mm to 400 mm

8466 10 200 0;

8466 20 200 0;

8466 20 980 0;

8486 90 100 0

1.2.2.

The machines provided below and any their combinations for processing or cutting of metals, ceramics or composition materials which according to technical specifications of the manufacturer can be equipped with electronic devices for simultaneous planimetric management on two or more axes:

Special note.

For ChPU blocks and the related software see Item 1.4.3

1.2.2.1.

The lathes having positioning accuracy with all compensation opportunities (less) than 6 microns according to the international standard ISO 230/2 are better (1988) or its national equivalent along any linear axis (the general choice of line item) for the machines suitable for processing of details with a diameter more than 35 mm

8457 20 000 0;

8457 30;

8458 11 200 0;

8458 11 490 0;

8458 91 200 9;

8464 90 000 0;

8465 20 000 0;

8465 99 000 0

Warning!!!

This is not a full text of document! Document shown in Demo mode!

If you have active License, please Login, or get License for Full Access.

With Full access you can get: full text of document, original text of document in Russian, attachments (if exist) and see History and Statistics of your work.

Get License for Full Access Now

Disclaimer! This text was translated by AI translator and is not a valid juridical document. No warranty. No claim. More info

Effectively work with search system

Database include more 50000 documents. You can find needed documents using search system. For effective work you can mix any on documents parameters: country, documents type, date range, teams or tags.
More about search system

Get help

If you cannot find the required document, or you do not know where to begin, go to Help section.

In this section, we’ve tried to describe in detail the features and capabilities of the system, as well as the most effective techniques for working with the database.

You also may open the section Frequently asked questions. This section provides answers to questions set by users.

Search engine created by SojuzPravoInform LLC. UI/UX design by Intelliants.